Lp stove hook up

How to hook up a gas range Photo 1: Pull out the range Pull out the range, and shut off the gas cock see also Photo 2. The gas is off when the lever is at a right angle to the pipe.

This shutoff may be located behind the range, or in the basement just below. Wrap the pipe threads Wrap Teflon pipe-joint tape twice around the threads in the same direction that the fitting screws on clockwise.

Yellow Teflon tape, heavier than white, is meant for gas fittings. Screw the connector to the gas line Remove the end connector fitting, wrap the unbeveled end with Teflon tape, and screw it to the gas line. This end fitting can be either male or female. NEVER screw the connector nuts that are on the ends of the corrugated tube to a black gas fitting or pipe.

This would be a guaranteed leak. Use Teflon tape on each fitting. Tighten the nuts Tighten the connector nuts to the two end connector fittings. While tightening the nuts, hold the tube straight against the fitting. Do NOT use Teflon tape on these threads. The beveled edges of the end fittings are meant to form a tight seal against the ends of the corrugated tube.

Using tape can interfere with this seal. Check for leaks Turn on the gas cock vertical position and light the range burners for about a minute to get the air out of the gas line. You can also use warm, thick soapy water for this.

Bubbles around a joint will indicate a leak. Hooking up a gas range or water heater is a relatively simple job requiring just basic tools and readily available supplies. And if you use the right materials and follow instructions carefully, you can safely do the job yourself.

A professional may charge as much as a few hundred dollars for a hook-up. Flexible corrugated gas connectors and gas pipe and fittings black are available at most home centers and well-stocked hardware stores. Stainless steel or coated brass connectors are the only type of flexible connectors sold these days, and the only type you can safely and legally use. Older types of corrugated connectorsósold until the sómade of uncoated brass or other metal have been found to be unsafe.

Have one in your house? The most important step to a safe installation is to buy the right connector. These dimensions are not always marked on the package, but they will be marked for either range or dryer. Buy a connector that comes packaged with the end connector fittings you need see Photo 3.

If you cannot find a connector package with end fittings that match what you need for the gas line, use a black gas pipe fitting on the line to accommodate the end connector fitting. They come in lengths from 24 in. Follow the instructions for installing the connector religiously. Our Photos 1 through 5 give a real-life picture of how this is done. Here are some additional guidelines: Be careful not to kink or force the corrugated connector into sharp bends, which could eventually cause a break.

Always check your work for leaks Photo 6. Gas leak detectors are sold at home centers, hardware stores and online. Hook up a gas water heater Photo 1: Shut off the gas Shut off the gas cock on the line entering the water heater. It usually requires a one-quarter turn. When the lever is parallel to the pipe, the gas is on; at a right angle to the pipe is off. Unscrew the union Uncouple the gas line at the union, a fitting that should be located somewhere below the gas cock, as shown here and in Photos 4 and 5.

Hold back the top part of the union with one wrench as you unscrew the coupling section with a second wrench. Unscrew the tee Remove the two short vertical lengths of pipe that run above and below the tee fitting.

Reassemble the gas line Reassemble the gas line in the same configuration as it was. Reassemble the union Reconnect the union. Note the copper seal that forms the gas-tight seal; make sure the pipe alignment is straight, so the two sections of the seal will join up properly.

Then tighten the union as shown in Photo 2. Install the drip leg and cap as shown in Photo 3. In many cases, the gas port on your new water heater will be in the same location as the old one, relative to your gas line. This makes the hook-up easy: Just remove the short lengths of pipe and fittings, as shown in Photos 2 and 3, clean the threads, apply new Teflon tape to the threads, and reconnect the entire assembly exactly as it was before.

Here are some guidelines: Use yellow Teflon tape, intended for threaded gas connections, not white Teflon tape, which is thinner. Test all your joints for leaks. In most, but not all areas, a permit and inspection is required for a water heater hookup. In either case, we strongly recommend that you call your local gas company or plumbing inspector to check your work.


Watch the pros install a propane gas stove. Similar Topics: Appliances. Related Videos. How to Install a Gas Cooktop Gas Fireplace Basics. How to Replace a Broken Window Pane 4 Steps. How to Hook Up the Gas for a Fire Pit 7 Steps. How to Refurbish a Gas Grill. How to Solder Copper Pipe Using a Propane Torch 3 Steps. How to . UL listed regulator and hose kit lets you hook up the propane stove above to your lb. propane tank or portable cylinder, not included. Mr. Heater LP Kit For Propane Stoves, Model# F | Northern Tool + EquipmentPrice: $

Total 2 comments.
#1 10.08.2018 –≤ 20:49 Ashowofhandsdvd:
Honestly, the right job

#2 15.08.2018 –≤ 18:48 Roman-Leslav:
Absolutely agree with you. This is a great idea. I support you.